use this link to access RSR webmail
Classified Ads
RSR Forum- Veteran/Vintage Rovers • 12hp Rover Tourer Clutch Advice RequiredHi All, New member in search of advice regarding a slipping clutch on a 1921 12hp Clegg Tourer. The car has been in the family for almost 40yrs but has lay idle for approximately 8yrs. It was started regularly but never driven in this time and yesterday was its first trip out but it was […]IrishRoverClegg
- Meetings, Rallies and Events • RSR Shropshire & Staffordshire Region meet tonight, 15th September 2026.TONIGHT The RSR Shropshire & Staffordshire Region meet tonight, 15th September 2026.Members and Rover enthusiasts are cordially invited with all Rovers to the monthly meet held on every third Tuesday of the month from 7.30 pm.SPECIAL NOTE....The location for SEPTEMBER is THE SPREAD EAGLE, Watling Street, Gailey, ST19 5PNThe Spread Eagle is a carvery and […]markgray
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Speedometer_CableHelloThank you, I got. one from a dealer in England.RegardsHelmuthhguss
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Speedometer_CableI got a new one from Mike at Meteor spares last year for my 1936 12 Tourer.Willem
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Speedometer_CableDear Helmuth,I was looking back and saw your post was unanswered. I suspect you had been trying Speedograph Richfield for this part. I am not aware that they would have been able to supply this component even when they were in business because it isn't a cable but rather a flexible shaft. The part number […]SHyslop
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: 1939 P2 R10 starter motorSimon,A dodge that I use is to mark both the starter motor and the housing with a straight line. This makes aligning the starter motor in the housing a doddle. There can be 2 holes in the starter's casing for the bolt (part 10841 and its locknut part 2094) to engage in. Finding the right […]GOY189
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: 1939 P2 R10 starter motorgood luck, I think the motor is generic and the housing is the Rover bit.ANDY
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Rover 12 tourer ~58 (the green one)I haven’t posted anything about this car for a while, but it has been going very well apart from a bit of electrical dramas which were fixed by a new electronic sold state cut out/ regulator. I had noticed that the engine compartment was getting a bit oily and it was leaving an excessive number […]David2021
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: No power from ignition switch to coil (sometimes)I watched the vid. Very informative. Scary to take the ignition switch to pieces. I’m hoping I don’t need to do it.And I’ve also found the solenoid (I’m not at the car, but searched through photos I had taken on first visit). So on next visit I can wire between solenoid and coil with a […]P27
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: No power from ignition switch to coil (sometimes)If you are in the Midlands you can try Vehicle Wiring Services near Tenbury Wells, they rewired my 1937 12 Tourer and I am sure they can figure out what's wrong with your electrics/ Coil etc.http://vehiclewiringservices.co.ukI did put a video on Youtube on the workings of the ignition switch, search for: Rover 12 tourer starter […]Willem
- Veteran/Vintage Rovers • 12hp Rover Tourer Clutch Advice Required
