Classified Ads
RSR Forum posts- Wilks' cars P1 and P2, thats cars up to 1947 • Re: rover 10 p2 steeringHi Andy,Yes there are different length columns and, therefore, different length control tubes. Also the later columns are a larger diameter so the indicator mechanism may be a fiddle to fit unless you have some later column parts.To resolve your problem you can try to extend the short control tube, get a longer replacement if […]TonyG
- Wilks' cars P1 and P2, thats cars up to 1947 • rover 10 p2 steering1939 P2 Rover 10 does anyone know if there are different lengths of steering control tube? I had to replace the steering column but I couldn't find the exact one so I settled for one that was very similar. The problem is the control tube is about 1" short and the horn assembly doesn't fit. […]ANDY
- Meetings, Rallies and Events • Re: RSR Shrops & Staffs Region meet tonight, 16th June 2026TONIGHT The RSR Shropshire & Staffordshire Region meet tonight, 16th June 2026.Members and Rover enthusiasts are cordially invited with all Rovers to the monthly meet held on every third Tuesday of the month from 7.30 pm.SPECIAL NOTE....The location for JUNE is THE SPREAD EAGLE, Watling Street, Gailey, ST19 5PNThe Spread Eagle is a carvery and […]markgray
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Clutch, and steering box refurbDear Willem,I would be very hopeful that the cause of the problem will be reasonably apparent once a very close look at all the dimensions is made. I was just thinking, something I am finding increasingly useful, is one of those endoscope cameras you can now buy for reasonable money, although mine was a Christmas […]SHyslop
- Veteran/Vintage Rovers • Re: Rover 10 Special Engine rebuildHi,it does not matter,i have a question for you,i am assembling my special 10 engine and was wondering if there is a locating screw in the rear camshaft bush in crankcase.Nello
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Clutch, and steering box refurbDear SH,thank you for your reply, here are the details, all exchange parts are from Mike Couldry3 lever clutch, exchange leversPressure plate, exchangeSpigot release bearing, exchangeSprings on levers, newFlywheel pilot earing, newI did notice that the exchange clutch plate is a bit thicker than the old one, stupidly I didn't take any measurements.I did see […]Willem
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Clutch, and steering box refurbDear Willem,I can only speculate based on my own experience two years ago replacing the clutch in my 1935 12 sports saloon. Now, your symptoms are different from what mine were because my clutch wouldn't disengage, once reassembled. Having had it to bits and back together in a week then apart again the next week, […]SHyslop
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Clutch, and steering box refurbI reassembled the car and I am seriously looking to pull the clutch out again, when I first started the car and depressed the clutch there was an almighty racket (rythmic thumping sound) and the engine stalled. Loosening the clutch cable to a very slack state has now reduced the noise to a very faint […]Willem
- Veteran/Vintage Rovers • Two twenties Rovers for auction on 13/6/26I thought that these two cars coming up for auction on the 13th of June might be of interest with the estimate for the first being £5000 - £7000 and £8000 - £10000 for the second.https://www.prewarcar.com/904980-1929-r ... sman-coupeI know nothing about the car, have never seen it in the metal and this post is just […]SHyslop
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: Choke control lightI found I had a better cover & even had the correct number! I fitted it & connected the wires and it works ! Result!David2021
- Wilks' cars P1 and P2, thats cars up to 1947 • Re: rover 10 p2 steering
